1、Screw jacks are put on the seat pads and adjusted to the same height using a leveling instrument. Then the screw jacks shall be fixed tightly and their positions recorded.(按圖紙標高，用水準儀校準到統一高度，按位置記錄并收緊螺紋千斤頂。)
2、This article focused on analysis of the tension screw on the quality of concrete in the shear wall and put forward some specific proposal measures.(本文就重點就對拉螺桿對剪力墻混凝土質量的影響進行分析，提出了幾點針對性的建議措施。)
3、On completing of the wire plugging, put the function items into the matching installation bottom cases respectively, and tighten the installation screws on the screw holes.(接好線的功能件放入與之匹配的安裝底盒，通過安裝螺絲孔擰緊安裝螺絲固定。)
4、Some solutions are put forward by analyzing reasons of burning loss for the screwdown screw and nut on steckel mill.(通過對爐卷軋機的壓下螺絲與螺母燒損的設備事故現象的分析，找出事故產生的原因，并提出了相應的解決方案。)
5、The positive pressure distribution on the bearing surface of screw down system of 950 primary mill was studied using FEM and the corresponding improvement way has been put forward.(通過有限元分析，研究了950開坯機壓下系統球面軸承表面正壓力的分布情況，并據此提出了相應的改進措施。)
6、The person on the car, and then on the brake pedal is motionless, the car under put irritating to repeat the process until the brake fluid flip so far no air, then loaded back to screw.(車上的人了，然后踩剎車踏板一動不動，車下的放刺激性重復這個過程，直到制動液翻轉到目前為止沒有空氣的時候，然后裝回螺絲。)
7、Based on the idea of spool's two degree of freedom motion authors put forward a new concept of servo screw.(在閥芯雙運動自由度的基礎上提出了一種流體伺服螺旋的概念。) hAo86.com
8、Some riders put a dab of nail polish on the binding's screw threads to help keep the screws in place.(有一些滑雪者會往固定器的螺絲上涂上指甲油保證螺絲不會松動。)
9、Put the absorbent cotton back into the tube, counterclockwise screw the tube on the cover tightly.(將吸透水的吸水棉放進套管內，將套管逆時針?lè)较蛐o在頂蓋上。)
10、Failure is more common with the screw put on the Bellows Seal Valves threaded stem wear, so that the valve can not close.(比較常見的故障是閥桿與螺套上的絲扣磨損，陶瓷閥門使閥門無法關閉。)
11、As to the problems of bearing disable, the mend method on seal structure of the screw conveyer for powder materiel is put forward, and the applied effect is demonstrated.(針對粉狀物料螺旋輸送機軸承損壞問題，提出了軸承密封結構的改進措施，說明了改進后的應用效果。)
12、Don't put the screw (s) on Mr. Chen.(不要給陳先生太多的壓力。)
